1、 Electric induction glass door daily cleaning manual:

1 、清理門扇運行路面，確保電動感應玻璃門的運作運動軌跡正下方?jīng)]有廢棄物及塵土，特別是全自動平（移）滑門的地滑軌要用吸塵機清理灰塵，卡死的臟東西要用醫用鑷子等專用工具清理（注意：避免劃傷軌道）

1. Clean the road surface of the door leaf to ensure that there is no waste or dust directly below the operation trajectory of the electric induction glass door. Especially, the ground slide of the fully automatic sliding door should be cleaned with a vacuum cleaner, and any stuck dirt should be cleaned with specialized tools such as medical tweezers (note: avoid scratching the track)

2 、保潔服務電動感應玻璃門時，需要先按住急停按鈕開關，選用軟抹布和中性洗滌劑。

2. When using electric induction glass doors for cleaning services, it is necessary to first press and hold the emergency stop button switch, select a soft cloth and neutral detergent.

3、 清理電動感應玻璃門的照明燈具時，請在照明燈具滅掉15分鐘后清理，以防燈夾層玻璃因為受寒粉碎。

3. When cleaning the lighting fixtures of the electric induction glass door, please clean them 15 minutes after the lighting fixtures are turned off to prevent the laminated glass of the lights from being crushed due to cold.

4、 在清理電動感應玻璃門發動機部件自動開關、感應元器件時，應留意電器性，嚴禁運作中感應起電開展保潔服務工作。

4. When cleaning the automatic switches and sensing components of the electric induction glass door engine components, attention should be paid to the safety of the electrical appliances. It is strictly prohibited to use induction power during operation to carry out cleaning services.

5 、在清理電動感應玻璃門的感應識別裝置及性光線傳感器時、電子監控等裝置時，應當心輕擦，以防刮及碰撞后更改電動感應玻璃門的控制器的感應視角和區域。

5. When cleaning the induction recognition device and safety light sensor of the electric induction glass door, electronic monitoring and other safety devices, care should be taken to wipe them gently to prevent scratching and changing the sensing angle and area of the controller of the electric induction glass door after collision.

6 、清理不銹鋼板等包邊條門邊框時，盡可能選用專用型清潔劑，針對氟碳漆、空氣氧化的表層。切勿選用強酸強堿腐蝕、特別是在是苯和甲苯等有機溶劑。

6. When cleaning stainless steel plates and other door frames with wrapped edges, special cleaning agents should be used as much as possible, targeting the surface layer of fluorocarbon paint and air oxidation. Do not use strong acids or alkalis for corrosion, especially in organic solvents such as benzene and toluene.

7、 禁止猛擊敲擊、自來水侵蝕電動感應玻璃門的門頁，立在電動感應玻璃門的門上邊爬行現澆板或雨罩。盡快密封門體上邊的防潮防水對策，以防電器透水性返潮毀壞。

7. It is prohibited to forcefully strike or tap water to corrode the door leaf of the electric induction glass door. Standing on the door of the electric induction glass door and crawling on the cast-in-place slab or rain cover. Seal the moisture-proof and waterproof measures on the top of the door body as soon as possible to prevent damage to the electrical permeability due to moisture regain.

8 、電動感應玻璃門暫停服務三個月左右，提議撥掉主電源線插頭，關掉UPS電源總開關。但若配備應急模塊，務必每三個月插上主開關電源對鋰電池組電池充電一次。

8. The electric induction glass door has been out of service for about three months. It is proposed to unplug the main power cord and turn off the UPS main switch. But if equipped with an emergency module, be sure to plug in the main switch power supply every three months to charge the lithium battery pack battery.